reflow-oven-control-sw/stm-firmware/main.c

/* Reflow Oven Controller
 *
 * Copyright (C) 2020  Mario Hüttel <mario.huettel@gmx.net>
 *
 * This file is part of the Reflow Oven Controller Project.
 *
 * The reflow oven controller is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * The Reflow Oven Control Firmware is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with the reflow oven controller project.
 * If not, see <http://www.gnu.org/licenses/>.
 */

/**
 * @file main.c
 * @brief Main file for firmware
 */

#include "reflow-controller/safety/safety-config.h"
#include <stdlib.h>
#include <stdio.h>
#include <string.h>
#include <stm32/stm32f4xx.h>
#include <cmsis/core_cm4.h>
#include <setup/system_stm32f4xx.h>
#include <reflow-controller/systick.h>
#include <reflow-controller/adc-meas.h>
#include <reflow-controller/digio.h>
#include <stm-periph/stm32-gpio-macros.h>
#include <stm-periph/rcc-manager.h>
#include <stm-periph/uart.h>
#include <reflow-controller/periph-config/shell-uart-config.h>
#include <reflow-controller/oven-driver.h>
#include <fatfs/ff.h>
#include <reflow-controller/sd.h>
#include <reflow-controller/ui/gui.h>
#include <reflow-controller/ui/shell.h>
#include <reflow-controller/ui/shell-uart.h>
#include <reflow-controller/safety/safety-controller.h>
#include <reflow-controller/settings/settings.h>
#include <reflow-controller/safety/safety-memory.h>
#include <reflow-controller/safety/fault.h>
#include <reflow-controller/updater/updater.h>
#include <reflow-controller/temp-profile/temp-profile-executer.h>
#include <reflow-controller/settings/spi-eeprom.h>
#include <reflow-controller/main-cycle-counter.h>
#include <stm-periph/option-bytes.h>

static void setup_nvic_priorities(void)
{
	/* No sub priorities */
	NVIC_SetPriorityGrouping(2);

	/* Setup Priorities */
	NVIC_SetPriority(ADC_IRQn, 2);
	/* Measurement ADC DMA */
	NVIC_SetPriority(DMA2_Stream0_IRQn, 1);
	/* Shelmatta UART TX */
	NVIC_SetPriority(DMA2_Stream7_IRQn, 3);
	NVIC_SetPriority(DMA2_Stream4_IRQn, 2);
}

FATFS fs;
#define fs_ptr (&fs)

/**
 * @brief Configure UART GPIOs
 * In case the application is build in debug mode, use the TX/RX Pins on the debug header
 * else the Pins on the DIGIO header are configured in the digio module and this function does nothing.
 */
static inline void uart_gpio_config(void)
{
#if defined(DEBUGBUILD) || defined(UART_ON_DEBUG_HEADER)
	rcc_manager_enable_clock(&RCC->AHB1ENR, BITMASK_TO_BITNO(SHELL_UART_PORT_RCC_MASK));
	SHELL_UART_PORT->MODER &=  MODER_DELETE(SHELL_UART_TX_PIN) & MODER_DELETE(SHELL_UART_RX_PIN);
	SHELL_UART_PORT->MODER |= ALTFUNC(SHELL_UART_RX_PIN) | ALTFUNC(SHELL_UART_TX_PIN);
	SETAF(SHELL_UART_PORT, SHELL_UART_RX_PIN, SHELL_UART_RX_PIN_ALTFUNC);
	SETAF(SHELL_UART_PORT, SHELL_UART_TX_PIN, SHELL_UART_TX_PIN_ALTFUNC);

	/* Setup Pullup resistor at UART RX */
	SHELL_UART_PORT->PUPDR |= PULLUP(SHELL_UART_RX_PIN);
#endif
}

/**
 * @brief Process the boot status structure in the safety (backup) RAM
 * Depending on the flags set there, this function will:
 *  - Reboot into the ram code for reflashing
 *  - Display the PANIC message
 *  - Display if the flash has been successfully updated
 */
static inline void handle_boot_status(void)
{
	struct safety_memory_boot_status status;
	int res;

	res = safety_memory_get_boot_status(&status);
	if (res != 0)
		panic_mode();

	if (status.reset_from_panic) {
		/* We've seen a panic */
		gui_root_menu_message_set("!! PANIC !!", "Check error me- mory!");
	}

	if (status.reboot_to_bootloader) {
		status.reboot_to_bootloader = 0UL;
		safety_memory_set_boot_status(&status);

		led_set(0, 1);
		led_set(1, 1);

		gui_lcd_write_direct_blocking(0, "Updating...");

		start_updater_ram_code();
	}

	if (status.code_updated) {
		status.code_updated = 0x0UL;
		safety_memory_set_boot_status(&status);

		/* Display notification on GUI */
		gui_root_menu_message_set("Firmware updated", "[Press Key]");
	}
}

/**
 * @brief Read out the option bytes of the STM32 and program them to the desired values.
 *
 * - This function currently forces the brown out level to Level 3.
 */
static void check_and_program_opt_bytes(void)
{
	struct option_bytes opts;
	int err;

	/** - Read option bytes */
	stm_option_bytes_read(&opts);


	if (opts.brown_out_level != 0) {
		/* Set the brown out level to level 3 => highest brown out limit. */
		opts.brown_out_level = 0;
		/** - Program the option bytes if brown out level was not set correctly */
		err = stm_option_bytes_program(&opts);

		/** - If programming failes, enter panic mode */
		if (err)
			panic_mode();

		/** - If programming is successful, reset the system to apply new settings */
		NVIC_SystemReset();
	}
}

/**
 * @brief Setup the system.
 *
 * This function does all basic initializations of the MCU and its peripherals
 */
static inline void setup_system(void)
{
	float tmp;

	/** - Read the option bytes and if necessary program them to the desired values */
	check_and_program_opt_bytes();

	/** - Setup the NVIC priorities of the core peripherals using interrupts */
	setup_nvic_priorities();

	/** - Init safety controller and safety memory */
	safety_controller_init();

	/** - Setup the systick module generating the 100us tick fort the GUI and
	 *  the 1ms tick for the global systick timestamp
	 */
	systick_setup();

	/** - Initialize the oven output driver outputting the wavepacket control signal for the SSR and */
	oven_driver_init();

	/** - Initialize all DIGIO Pins to their default state and pin functions */
	digio_init();

	/** - Set-up the LED outputs */
	led_setup();

	/** - Set-up the loudspeaker / beeper output */
	loudspeaker_setup();

	/** - Initialize the GUI */
	gui_init();

	/** - Initialize the pins for the uart interface. */
	uart_gpio_config();

	/** - Set-up the settings module */
	settings_setup();

	/** - Load the overtemperature limit from eeprom if available. Otherwise the default value will be used */
	if (settings_load_overtemp_limit(&tmp) == SETT_LOAD_SUCCESS)
		safety_controller_set_overtemp_limit(tmp);

	/** - Handle the boot status struct in the safety memory */
	handle_boot_status();

	/** - Initialize the shell UART */
	shell_uart_setup();

	/** - Enable the ADC for PT1000 measurement */
	adc_pt1000_setup_meas();

	/** - Enable the misc CRC config monitor to supervise clock, systick and flash settings */
	(void)safety_controller_set_crc_monitor(ERR_CRC_MON_MISC, SAFETY_CRC_MON_MISC_PW);
}

/**
 * @brief Handle the input for the shell instance.
 *
 * This function will check if the RX ring buffer of the UART contains data.
 * If so, it will prowvide it to the shellmatta shell.
 *
 * @param shell_handle Handle to the shellmatta instance
 */
static void handle_shell_uart_input(shellmatta_handle_t shell_handle)
{
	int uart_receive_status;
	const char *uart_input;
	size_t uart_input_len;

	/* Handle UART input for shell */
	uart_receive_status = shell_uart_receive_data_with_dma(&uart_input, &uart_input_len);
	if (uart_receive_status >= 0)
		shell_handle_input(shell_handle, uart_input, uart_input_len);
}

/**
 * @brief This is the main function containing the initilizations and the cyclic main loop
 * @return Don't care. This function will never return. We're on an embedded device...
 */
int main(void)
{
	bool cal_active;
	float offset;
	float sens;
	int status;
	bool sd_card_mounted = false;
	bool sd_old;
	shellmatta_handle_t shell_handle;
	int menu_wait_request;
	uint64_t quarter_sec_timestamp = 0ULL;
	enum config_weight worst_safety_flag = SAFETY_FLAG_CONFIG_WEIGHT_NONE;

	/** - Setup all the peripherals and external componets like LCD, EEPROM etc. and the safety controller */
	setup_system();

	/** - Try load the calibration. This will only succeed if there's an EEPROM */
	status = settings_load_calibration(&sens, &offset);
	if (!status)
		adc_pt1000_set_resistance_calibration(offset, sens, true);

	/** - Initialize the shellmatta shell */
	shell_handle = shell_init(shell_uart_write_callback);

	/** - Print motd to shell */
	shell_print_motd(shell_handle);

	/** - Set the main cycle counter to 0 and activate the core cycle counter if available */
	main_and_core_cycle_counter_init();

	/** - Do a loop over the following */
	while (1) {

		/** - If 250 ms have passed since the last time this step was reached, we try to initialize the
		 *  SD card. If the card has been mounted and there is no current resistance calibration,
		 *  it is tried to load it from SD card.
		 */
		if (systick_ticks_have_passed(quarter_sec_timestamp, 250)) {
			led_set(1u, 0);
			sd_old = sd_card_mounted;
			sd_card_mounted = mount_sd_card_if_avail(fs_ptr);

			if (sd_card_mounted && !sd_old) {
				adc_pt1000_get_resistance_calibration(NULL, NULL, &cal_active);
				if (!cal_active) {
					status = settings_load_calibration(&sens, &offset);
					if (!status)
						adc_pt1000_set_resistance_calibration(offset, sens, true);
				}
			}

			/* Check if any flags are present, that disable the PID controller. Blink
			 * LED 0 in this case
			 */
			if (worst_safety_flag >= SAFETY_FLAG_CONFIG_WEIGHT_PID)
				led_set(0u, led_get(0u) ? 0 : 1);
			else
				led_set(0u, 0);

			quarter_sec_timestamp = systick_get_global_tick();
		}

		/** - Handle the GUI */
		menu_wait_request = gui_handle();

		/** - Handle the uart input for the shell */
		handle_shell_uart_input(shell_handle);

		/** - Execute current profile step, if a profile is active */
		temp_profile_executer_handle();

		/** - Handle the safety controller. This must be called! Otherwise a watchdog reset will occur */
		worst_safety_flag = safety_controller_handle();

		/** - If the Oven PID controller is running, we handle its sample function */
		if (oven_pid_get_status() == OVEN_PID_RUNNING)
			oven_pid_handle();

		/** - Apply the power level of the oven driver */
		oven_driver_apply_power_level();

		/** - Report the main loop timing to the timing monitor to detect a slowed down main loop */
		safety_controller_report_timing(ERR_TIMING_MAIN_LOOP);

		/** - If the menu requests a directly following loop run, the main loop will continue.
		 *  Otherwise it will wait for the next interrupt
		 */
		if (menu_wait_request)
			__WFI();
		else
			__NOP();
		/** - Increment the main cycle counter */
		main_cycle_counter_inc();
	}

	return 0;
}

/**
 * @brief Callback function for the SDIO driver to wait \p ms milliseconds
 * @param ms
 * @warning This function relies on the systick and must not be used in interrupt context.
 */
void sdio_wait_ms(uint32_t ms)
{
	systick_wait_ms(ms);
}