734 lines
17 KiB
C
734 lines
17 KiB
C
#include "shimatta_sdio.h"
|
|
#include "shimatta_sdio_config.h"
|
|
#include <cmsis/core_cm4.h>
|
|
#include <stm32/stm32f4xx.h>
|
|
|
|
extern void sdio_wait_ms(unsigned int i);
|
|
|
|
#define SETAF(PORT,PIN,AF) PORT->AFR[(PIN < 8 ? 0 : 1)] |= AF << ((PIN < 8 ? PIN : (PIN - 8)) * 4)
|
|
|
|
#define READCTRL ((BLOCKSIZE << 4) | SDIO_DCTRL_DMAEN)
|
|
#define DMAP2M (DMA_SxCR_CHSEL_2 | DMA_SxCR_PBURST_0 | DMA_SxCR_MBURST_0 | DMA_SxCR_MSIZE_1 | DMA_SxCR_PSIZE_1 | DMA_SxCR_MINC | DMA_SxCR_PFCTRL)
|
|
#define DMAM2P (DMA_SxCR_CHSEL_2 | DMA_SxCR_PBURST_0 | DMA_SxCR_MBURST_0 | DMA_SxCR_MSIZE_1 | DMA_SxCR_PSIZE_1 | DMA_SxCR_MINC | DMA_SxCR_PFCTRL | DMA_SxCR_DIR_0)
|
|
#define SHORT_ANS 1
|
|
#define LONG_ANS 3
|
|
#define NO_ANS 0
|
|
|
|
#define CCRCFAIL 1
|
|
#define CTIMEOUT 2
|
|
#define CNOTEXPETED 3
|
|
|
|
/* OCR Register Masks */
|
|
#define OCS_CCS (1<<30)
|
|
#define OCS_BUSY (1<<31)
|
|
|
|
enum acmd41_ret {ACMD41_RESP_INIT = 0, ACMD41_RESP_ERR, ACMD41_RESP_SDSC, ACMD41_RESP_SDXC};
|
|
enum cmd8_ret {CMD8_RESP_TIMEOUT = 0, CMD8_VOLTAGE_ACCEPTED, CMD8_VOLTAGE_DENIED};
|
|
typedef uint8_t CID_t;
|
|
|
|
static struct sd_info card_info; // = {.type = CARD_NONE};
|
|
|
|
/**
|
|
* @brief checkNotInserted
|
|
* @return return 0 if card is inserted, else 1
|
|
*/
|
|
int sdio_check_inserted() {
|
|
#if SDIO_ENABLE_INS
|
|
return ((INS_PORT->IDR & (1<<INS_PIN)) == (INS_ACTIVE_LEVEL<<INS_PIN) ? 0 : 1);
|
|
#else
|
|
return 0; // Assume Card is inserted
|
|
#endif
|
|
}
|
|
|
|
/**
|
|
* @brief checkWriteProtection
|
|
* @return 0 if card is writable.
|
|
*/
|
|
static int sdio_check_write_protection() {
|
|
#if SDIO_ENABLE_WRITEPROT
|
|
return ((WRITEPROT_PORT->IDR & (1<<WRITEPROT_PIN)) == (WRITEPROT_ACTIVE_LEVEL<<WRITEPROT_PIN) ? 1 : 0);
|
|
#else
|
|
return 0; // Assume Card is not write protected
|
|
#endif
|
|
}
|
|
|
|
static void sdio_wait_cmd_sent()
|
|
{
|
|
while (!(SDIO->STA & SDIO_STA_CMDSENT));
|
|
SDIO->ICR |= SDIO_ICR_CMDSENTC;
|
|
}
|
|
|
|
static int sdio_send_cmd(uint8_t cmd, uint32_t arg, uint8_t expected_ans){
|
|
/* Clear Flags */
|
|
SDIO->ICR = SDIO_ICR_CCRCFAILC | SDIO_ICR_CMDRENDC | SDIO_ICR_CTIMEOUTC | SDIO_ICR_CMDSENTC;
|
|
/* Send command */
|
|
SDIO->ARG = arg;
|
|
SDIO->CMD = (cmd & SDIO_CMD_CMDINDEX) | SDIO_CMD_CPSMEN | ((expected_ans << 6) & SDIO_CMD_WAITRESP);
|
|
return 0;
|
|
}
|
|
|
|
static int sdio_get_response(uint8_t expected_command, uint8_t type_of_answer, uint32_t *response_buffer) {
|
|
uint32_t sdio_status;
|
|
|
|
/* Wait until command isn't active anymore */
|
|
while (SDIO->STA & SDIO_STA_CMDACT);
|
|
|
|
/* Wait for error or success */
|
|
while (1) {
|
|
sdio_status = SDIO->STA;
|
|
|
|
/* Check if a valid response was received */
|
|
if (sdio_status & SDIO_STA_CMDREND)
|
|
break;
|
|
|
|
if ((sdio_status & SDIO_STA_CMDSENT) && (type_of_answer == NO_ANS))
|
|
break; // No response required
|
|
|
|
/* Exclude ACMD41 and CMD2 from valid CRC check */
|
|
if ((sdio_status & SDIO_STA_CCRCFAIL)) {
|
|
if(expected_command == 0xff) {
|
|
break;
|
|
} else {
|
|
return -CCRCFAIL;
|
|
}
|
|
}
|
|
|
|
if (sdio_status & SDIO_STA_CTIMEOUT)
|
|
return -CTIMEOUT;
|
|
}
|
|
|
|
/* Valid Respone Received */
|
|
if (((SDIO->RESPCMD & SDIO_RESPCMD_RESPCMD) != expected_command) && (expected_command != 0xff))
|
|
return -CNOTEXPETED; //Not the expected respose
|
|
|
|
/* If case of a correct Response */
|
|
*(response_buffer++) = SDIO->RESP1;
|
|
|
|
/* Long response */
|
|
if (type_of_answer == LONG_ANS) {
|
|
*(response_buffer++) = SDIO->RESP2;
|
|
*(response_buffer++) = SDIO->RESP3;
|
|
*(response_buffer++) = SDIO->RESP4;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* @brief Switch the card to application mode. It now accepts ACMDXX commands
|
|
* @return 0 if successfuls
|
|
*/
|
|
static int sdio_switch_appmode_cmd55()
|
|
{
|
|
int retry = 0x20;
|
|
union sdio_status_conv converter;
|
|
uint32_t response;
|
|
do {
|
|
/* Execute Command and check for valid response */
|
|
sdio_send_cmd(55, (card_info.rca<<16)&0xFFFF0000, SHORT_ANS);
|
|
|
|
if (!sdio_get_response(55, SHORT_ANS, &response))
|
|
{
|
|
/* Response valid. Check if Card has accepted switch to application command mode */
|
|
converter.value = response;
|
|
if (converter.statusstruct.APP_CMD == 1)
|
|
return 0;
|
|
}
|
|
} while (--retry > 0);
|
|
|
|
return -1;
|
|
}
|
|
|
|
enum acmd41_ret sdio_init_card_acmd41(uint8_t HCS){
|
|
uint32_t response;
|
|
int retry = 0x20;
|
|
if (sdio_switch_appmode_cmd55())
|
|
return ACMD41_RESP_ERR;
|
|
|
|
do {
|
|
sdio_send_cmd(41, (HCS ? (1<<30) : 0) | (1<<28) | (1<<20) |(1<<21)|(1<<22) |(1<<23)|(1<<19), SHORT_ANS);
|
|
if (!sdio_get_response(0xFF, SHORT_ANS, &response)) {
|
|
if (response & OCS_BUSY) {
|
|
/* Card is ready... Who knows why this bit is called busy */
|
|
if (response & OCS_CCS) {
|
|
return ACMD41_RESP_SDXC;
|
|
} else {
|
|
return ACMD41_RESP_SDSC;
|
|
}
|
|
} else {
|
|
return ACMD41_RESP_INIT;
|
|
}
|
|
}
|
|
} while (--retry > 0);
|
|
|
|
return ACMD41_RESP_ERR;
|
|
}
|
|
|
|
static int sdio_send_csd_cmd9(uint16_t rca, uint32_t *response_buffer) {
|
|
int timeout = 0x20;
|
|
int res;
|
|
|
|
do {
|
|
sdio_send_cmd(9, (rca<<16)&0xFFFF0000, LONG_ANS);
|
|
res = sdio_get_response(0xFF, LONG_ANS, response_buffer);
|
|
if (!res)
|
|
break;
|
|
} while (--timeout > 0);
|
|
|
|
return res;
|
|
}
|
|
|
|
/**
|
|
* @brief Send data buffer to SD card
|
|
* @param dlen Data length. Must be a multiple of 4 bytes
|
|
* @param blklen Log2 of block length (9 in case of 512 byte block)
|
|
* @param buff Buffer to send
|
|
*/
|
|
static void sdio_write_buffer(uint32_t dlen, uint32_t log_blklen, const unsigned char *buff)
|
|
{
|
|
uint32_t count;
|
|
int byte_count;
|
|
int byte_max;
|
|
uint32_t fifo;
|
|
|
|
SDIO->DLEN = dlen;
|
|
|
|
/* Init Transfer */
|
|
SDIO->ICR = SDIO_ICR_CCRCFAILC | SDIO_ICR_DCRCFAILC | SDIO_ICR_CTIMEOUTC | SDIO_ICR_DTIMEOUTC |
|
|
SDIO_ICR_TXUNDERRC | SDIO_ICR_RXOVERRC | SDIO_ICR_CMDRENDC | SDIO_ICR_CMDSENTC | SDIO_ICR_DATAENDC |
|
|
SDIO_ICR_STBITERRC | SDIO_ICR_DBCKENDC | SDIO_ICR_SDIOITC | SDIO_ICR_CEATAENDC;
|
|
SDIO->DCTRL = (log_blklen<<4) | SDIO_DCTRL_DTEN;
|
|
|
|
for (count = 0; count < dlen; count += 4) {
|
|
fifo = 0;
|
|
|
|
if ((dlen - count) < 4)
|
|
byte_max = dlen - count;
|
|
else
|
|
byte_max = 4;
|
|
|
|
for (byte_count = 0; byte_count < byte_max; byte_count++) {
|
|
fifo >>= 8;
|
|
fifo |= (((uint32_t)*(buff++)) << 24) & 0xFF000000;
|
|
}
|
|
|
|
/* Wait as long as FIFO is full */
|
|
while (SDIO->STA & SDIO_STA_TXFIFOF);
|
|
|
|
/* Write data to FIFO */
|
|
SDIO->FIFO = fifo;
|
|
}
|
|
|
|
/* Wait for TX to complete */
|
|
while (SDIO->STA & SDIO_STA_TXACT);
|
|
}
|
|
|
|
static int sdio_send_write_block_cmd24(uint32_t addr)
|
|
{
|
|
uint32_t response;
|
|
|
|
sdio_send_cmd(24, addr, SHORT_ANS);
|
|
|
|
return sdio_get_response(24, SHORT_ANS, &response);
|
|
}
|
|
|
|
static int sdio_check_status_register_cmd13(uint16_t rca, uint32_t *status)
|
|
{
|
|
int timeout = 0x20;
|
|
uint32_t response;
|
|
int res;
|
|
|
|
do {
|
|
sdio_send_cmd(13, (rca<<16)&0xFFFF0000, SHORT_ANS);
|
|
if (!(res = sdio_get_response(13, SHORT_ANS, &response))) {
|
|
*status = response;
|
|
break;
|
|
}
|
|
} while (--timeout > 0);
|
|
|
|
return res;
|
|
}
|
|
|
|
static int sdio_send_bus_width_acmd6(uint8_t bus_width)
|
|
{
|
|
uint32_t response;
|
|
int retry = 0x20;
|
|
int ret;
|
|
|
|
if (sdio_switch_appmode_cmd55()) return -1;
|
|
do {
|
|
sdio_send_cmd(0x6, (bus_width == 4 ? 0x2 : 0x0), SHORT_ANS);
|
|
ret = sdio_get_response(0x6, SHORT_ANS, &response);
|
|
if (!ret)
|
|
return 0;
|
|
|
|
} while (--retry > 0);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
static int sdio_get_sector_count(uint16_t rca, uint32_t *sector_count)
|
|
{
|
|
uint32_t csd[4];
|
|
int res;
|
|
uint32_t size, mult, read_len, csd_rev;
|
|
|
|
if ((res = sdio_send_csd_cmd9(rca, csd))) {
|
|
return -1;
|
|
}
|
|
|
|
csd_rev = ((csd[0] >> 30) & (0x3));
|
|
|
|
if (csd_rev == 0) {
|
|
/* SD v1 Card */
|
|
size = ((csd[1] & 0x3FF) <<2) | (((csd[2]) & ((1<<31) | (1<<30)))>>30);
|
|
mult = ((csd[2] & ((1<<17)|(1<<16)|(1<<15)))>>15);
|
|
read_len = (1<<((csd[1] & ((1<<19)|(1<<18)|(1<<17)|(1<<16)))>>16));
|
|
*sector_count = (((size +1)*(1<<(mult+2))*read_len) >> BLOCKSIZE);
|
|
} else if (csd_rev == 1) {
|
|
/* SD v2 Card */
|
|
size = (((csd[1] & 0x3F)<<16) | ((csd[2] & 0xFFFF0000) >> 16));
|
|
*sector_count = (size << (19-BLOCKSIZE));
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* @brief Switch the SDIo prescaler
|
|
* @param Prescaler value
|
|
*/
|
|
static void sdio_switch_prescaler(uint8_t clkdiv)
|
|
{
|
|
uint32_t reg;
|
|
reg = SDIO->CLKCR;
|
|
/* Clear prescaler */
|
|
reg &= ~SDIO_CLKCR_CLKDIV;
|
|
/* Set bits */
|
|
reg |= (SDIO_CLKCR_CLKDIV & clkdiv);
|
|
SDIO->CLKCR = reg;
|
|
}
|
|
|
|
/**
|
|
* @brief initDetectandProtectionPins
|
|
*/
|
|
static void sdio_init_detect_pins()
|
|
{
|
|
#if SDIO_ENABLE_WRITEPROT==1
|
|
WRITEPROT_PORT->PUPDR |= ((WRITEPROT_PULLUP ? 1 : 0)<<WRITEPROT_PIN*2);
|
|
#endif /* SDIO_ENABLE_WRITEPROT */
|
|
#if SDIO_ENABLE_INS==1
|
|
INS_PORT->PUPDR |= ((INS_PULLUP? 1 : 0)<<INS_PIN*2);
|
|
#endif /* SDIO_ENABLE_INS */
|
|
__DSB();
|
|
}
|
|
|
|
static void sdio_init_hw()
|
|
{
|
|
//Init Clocks
|
|
RCC->AHB1ENR |= PORTCLKMASK | RCC_AHB1ENR_DMA2EN;
|
|
RCC->APB2ENR |= RCC_APB2ENR_SDIOEN;
|
|
//Init Alternate Functions
|
|
CLKPORT->MODER |= (2<<CLKPIN*2);
|
|
D0PORT->MODER |= (2<<D0PIN*2);
|
|
D0PORT->PUPDR |= (1<<D0PIN*2);
|
|
CMDPORT->MODER |= (2<<CMDPIN*2);
|
|
CMDPORT->PUPDR |= (1<<CMDPIN*2);
|
|
#if BUSWIDTH==4
|
|
D1PORT->MODER |= (2<<D1PIN*2);
|
|
D1PORT->PUPDR |= (1<<D1PIN*2);
|
|
D2PORT->MODER |= (2<<D2PIN*2);
|
|
D2PORT->PUPDR |= (1<<D2PIN*2);
|
|
D3PORT->MODER |= (2<<D3PIN*2);
|
|
D3PORT->PUPDR |= (1<<D3PIN*2);
|
|
#endif
|
|
//CLKPORT->AFR[(CLKPIN < 8 ? 0 : 1)] |= ALTFUNC << ((CLKPIN < 8 ? CLKPIN : (CLKPIN - 8)) * 4);
|
|
SETAF(CLKPORT, CLKPIN, ALTFUNC);
|
|
SETAF(CMDPORT, CMDPIN, ALTFUNC);
|
|
SETAF(D0PORT, D0PIN, ALTFUNC);
|
|
#if BUSWIDTH==4
|
|
SETAF(D1PORT, D1PIN, ALTFUNC);
|
|
SETAF(D2PORT, D2PIN, ALTFUNC);
|
|
SETAF(D3PORT, D3PIN, ALTFUNC);
|
|
#endif
|
|
|
|
|
|
//Init Module
|
|
|
|
//Set CLK Control Register
|
|
SDIO->CLKCR = (HW_FLOW<<14) | ((BUSWIDTH == 4 ? 1 : 0)<<11) | SDIO_CLKCR_CLKEN |
|
|
(INITCLK & SDIO_CLKCR_CLKDIV);
|
|
|
|
//Set Data Timeout
|
|
SDIO->DTIMER = DTIMEOUT;
|
|
|
|
//Set Data Parameters
|
|
//SDIO->DCTRL = (BLOCKSIZE << 4) | SDIO_DCTRL_DMAEN;
|
|
//Set Power Register: Power up Card CLK
|
|
SDIO->POWER = SDIO_POWER_PWRCTRL_0 | SDIO_POWER_PWRCTRL_1;
|
|
|
|
}
|
|
|
|
static int sdio_send_read_block_cmd17(uint32_t addr)
|
|
{
|
|
uint32_t response;
|
|
|
|
sdio_send_cmd(17, addr, SHORT_ANS);
|
|
return sdio_get_response(17, SHORT_ANS, &response);
|
|
}
|
|
|
|
static int sdio_send_all_send_cid_cmd2()
|
|
{
|
|
uint32_t response[4];
|
|
int ret;
|
|
int retry = 0x20;
|
|
|
|
do {
|
|
sdio_send_cmd(2, 0, LONG_ANS);
|
|
if (!(ret = sdio_get_response(0xFF, LONG_ANS, response)))
|
|
return 0;
|
|
} while (retry-- > 0);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int sdio_send_relative_address_cmd3(uint16_t* rca)
|
|
{
|
|
uint32_t response;
|
|
int retry = 0x20;
|
|
|
|
do {
|
|
sdio_send_cmd(3, 0, SHORT_ANS);
|
|
if (!sdio_get_response(3, SHORT_ANS, &response)) {
|
|
// TODO: Do some *optional* checking
|
|
*rca = ((response & 0xFFFF0000) >> 16);
|
|
return 0;
|
|
}
|
|
} while (retry-- > 0);
|
|
return -1;
|
|
}
|
|
|
|
static int sdio_send_go_idle_cmd0() {
|
|
sdio_send_cmd(0, 0x0, NO_ANS);
|
|
sdio_wait_cmd_sent();
|
|
return 0;
|
|
}
|
|
|
|
static enum cmd8_ret sdio_send_iface_condition_cmd8()
|
|
{
|
|
uint32_t response;
|
|
int res = 0;
|
|
int retry = 0x20;
|
|
|
|
do {
|
|
sdio_send_cmd(8, 0x1CC, SHORT_ANS); // 3.3V supply requesR
|
|
res = sdio_get_response(8, SHORT_ANS, &response);
|
|
if (res == 0) {
|
|
if (response & 0x100)
|
|
return CMD8_VOLTAGE_ACCEPTED;
|
|
else
|
|
return CMD8_VOLTAGE_DENIED;
|
|
}
|
|
} while (retry-- > 0);
|
|
|
|
return CMD8_RESP_TIMEOUT;
|
|
}
|
|
|
|
static int sdio_send_block_length_cmd16(uint32_t blocklen) {
|
|
int timeout = 0x20;
|
|
int res;
|
|
uint32_t response;
|
|
|
|
do {
|
|
sdio_send_cmd(16, blocklen, SHORT_ANS);
|
|
if (!(res = sdio_get_response(16, SHORT_ANS, &response))) {
|
|
return 0;
|
|
}
|
|
}while(--timeout > 0);
|
|
|
|
return res;
|
|
}
|
|
|
|
static int sdio_send_select_card_cmd7(uint16_t rca) {
|
|
int timeout = 0x20;
|
|
uint32_t response;
|
|
union sdio_status_conv status;
|
|
int res;
|
|
|
|
/* Send CMD7. Selects card */
|
|
do {
|
|
sdio_send_cmd(7, (rca<<16)&0xFFFF0000, SHORT_ANS);
|
|
if (!(res = sdio_get_response(7, SHORT_ANS, &response))) {
|
|
break;
|
|
}
|
|
} while(--timeout > 0);
|
|
|
|
/* Check, if card in in TRANS state */
|
|
if (sdio_check_status_register_cmd13(rca, &(status.value)))
|
|
res = -1;
|
|
if (status.statusstruct.CURRENT_STATE != CURRENT_STATE_TRAN)
|
|
res = -2;
|
|
return res;
|
|
}
|
|
|
|
DSTATUS sdio_status()
|
|
{
|
|
DSTATUS returnval = 0;
|
|
|
|
if (sdio_check_inserted())
|
|
returnval |= STA_NODISK;
|
|
|
|
if (card_info.type == CARD_NONE)
|
|
returnval |= STA_NOINIT;
|
|
|
|
if (sdio_check_write_protection())
|
|
returnval |= STA_PROTECT;
|
|
|
|
return returnval;
|
|
}
|
|
|
|
DRESULT sdio_disk_ioctl(BYTE cmd, void* buff){
|
|
DRESULT res = RES_OK;
|
|
|
|
switch(cmd) {
|
|
case GET_BLOCK_SIZE:
|
|
*((DWORD*)buff) = (DWORD)0x01;
|
|
break;
|
|
case GET_SECTOR_SIZE:
|
|
*((WORD*)buff) = (WORD)(1<<BLOCKSIZE);
|
|
break;
|
|
case GET_SECTOR_COUNT:
|
|
if (card_info.type != CARD_NONE) {
|
|
*((DWORD*)buff) = (DWORD)card_info.sector_count;
|
|
} else {
|
|
res = RES_ERROR;
|
|
}
|
|
break;
|
|
case CTRL_SYNC:
|
|
res = RES_OK;
|
|
break;
|
|
default:
|
|
res = RES_PARERR;
|
|
break;
|
|
}
|
|
|
|
return res;
|
|
}
|
|
|
|
DWORD __attribute__((weak)) get_fattime()
|
|
{
|
|
return (1<<16) | (1<<24); // return Jan. 1st 1980 00:00:00
|
|
}
|
|
|
|
DSTATUS sdio_initialize(){
|
|
int timeout = 0x3000;
|
|
enum cmd8_ret res8;
|
|
enum acmd41_ret resa41;
|
|
uint8_t hcs_flag = 0;
|
|
card_info.rca = 0;
|
|
card_info.type = CARD_NONE;
|
|
enum sdio_card_type detected_card = CARD_NONE;
|
|
|
|
sdio_init_hw();
|
|
sdio_wait_ms(2);
|
|
sdio_init_detect_pins();
|
|
if (sdio_check_inserted()) {
|
|
return STA_NOINIT | STA_NODISK;
|
|
}
|
|
|
|
sdio_send_go_idle_cmd0();
|
|
|
|
sdio_wait_ms(2);
|
|
|
|
res8 = sdio_send_iface_condition_cmd8();
|
|
switch (res8) {
|
|
case CMD8_VOLTAGE_ACCEPTED: // SDV2 Card
|
|
hcs_flag = 1;
|
|
break;
|
|
case CMD8_VOLTAGE_DENIED: // should not happen
|
|
return STA_NOINIT;
|
|
break;
|
|
case CMD8_RESP_TIMEOUT: // SDV1 Card
|
|
hcs_flag=0;
|
|
break;
|
|
default:
|
|
return STA_NOINIT;
|
|
break;
|
|
}
|
|
|
|
do {
|
|
//SDIO_wait_ms(2);
|
|
resa41 = sdio_init_card_acmd41(hcs_flag);
|
|
} while ((resa41 == ACMD41_RESP_INIT) && (--timeout > 0));
|
|
|
|
switch (resa41) {
|
|
case ACMD41_RESP_SDSC:
|
|
detected_card = (hcs_flag ? SD_V2_SC : SD_V1);
|
|
break;
|
|
case ACMD41_RESP_SDXC:
|
|
detected_card = SD_V2_HC;
|
|
break;
|
|
default:
|
|
return STA_NOINIT;
|
|
break;
|
|
}
|
|
|
|
if (sdio_send_all_send_cid_cmd2())
|
|
return STA_NOINIT;
|
|
|
|
if (sdio_send_relative_address_cmd3(&card_info.rca))
|
|
return STA_NOINIT;
|
|
if (sdio_get_sector_count(card_info.rca, &card_info.sector_count))
|
|
return STA_NOINIT;
|
|
if (sdio_send_select_card_cmd7(card_info.rca))
|
|
return STA_NOINIT;
|
|
|
|
if (sdio_send_block_length_cmd16((uint32_t)(1<<BLOCKSIZE)))
|
|
return STA_NOINIT;
|
|
|
|
if (sdio_send_bus_width_acmd6(BUSWIDTH))
|
|
return STA_NOINIT;
|
|
|
|
sdio_switch_prescaler(WORKCLK);
|
|
|
|
card_info.type = detected_card;
|
|
|
|
if (sdio_check_write_protection()) {
|
|
return STA_PROTECT;
|
|
} else
|
|
return 0;
|
|
}
|
|
|
|
DRESULT sdio_disk_read(BYTE *buff, DWORD sector, UINT count){
|
|
uint32_t addr;
|
|
uint32_t sdio_status;
|
|
uint32_t fifo;
|
|
uint32_t counter;
|
|
|
|
addr = (card_info.type == SD_V2_HC ? (sector) : (sector*512));
|
|
for (; count > 0; count--) {
|
|
|
|
/* configure read DMA */
|
|
// DMA2->LIFCR = 0xffffffff;
|
|
// DMA2->HIFCR = 0xffffffff;
|
|
// DMASTREAM->NDTR = 0;
|
|
// DMASTREAM->FCR = DMA_SxFCR_FTH_0 | DMA_SxFCR_FTH_1 | DMA_SxFCR_DMDIS;
|
|
// DMASTREAM->M0AR = (uint32_t)(buff);
|
|
// DMASTREAM->PAR = (uint32_t)&(SDIO->FIFO);
|
|
// DMASTREAM->CR = DMAP2M | DMA_SxCR_PL_1 | DMA_SxCR_PL_1;
|
|
// DMASTREAM->CR |= DMA_SxCR_EN;
|
|
|
|
SDIO->DLEN = (1 << BLOCKSIZE);
|
|
|
|
SDIO->ICR = SDIO_ICR_CCRCFAILC | SDIO_ICR_DCRCFAILC | SDIO_ICR_CTIMEOUTC | SDIO_ICR_DTIMEOUTC |
|
|
SDIO_ICR_TXUNDERRC | SDIO_ICR_RXOVERRC | SDIO_ICR_CMDRENDC | SDIO_ICR_CMDSENTC | SDIO_ICR_DATAENDC |
|
|
SDIO_ICR_STBITERRC | SDIO_ICR_DBCKENDC | SDIO_ICR_SDIOITC | SDIO_ICR_CEATAENDC;
|
|
SDIO->DCTRL = (BLOCKSIZE<<4) | SDIO_DCTRL_DTDIR | /*SDIO_DCTRL_DMAEN |*/ SDIO_DCTRL_DTEN;
|
|
|
|
/* Init Transfer */
|
|
if (sdio_send_read_block_cmd17(addr)) {
|
|
return RES_ERROR;
|
|
}
|
|
|
|
counter = 0;
|
|
while (counter < (1<<(BLOCKSIZE-2)) || !(SDIO->STA & (SDIO_STA_DBCKEND | SDIO_STA_DATAEND))) {
|
|
/* TODO: Handle errors */
|
|
if (SDIO->STA & (SDIO_STA_DCRCFAIL | SDIO_STA_DTIMEOUT | SDIO_STA_STBITERR))
|
|
{
|
|
return RES_ERROR;
|
|
}
|
|
|
|
if (SDIO->STA & SDIO_STA_RXDAVL) {
|
|
counter++;
|
|
fifo = SDIO->FIFO;
|
|
*(buff++) = (BYTE)(fifo & 0xFF);
|
|
fifo >>= 8;
|
|
*(buff++) = (BYTE)(fifo & 0xFF);
|
|
fifo >>= 8;
|
|
*(buff++) = (BYTE)(fifo & 0xFF);
|
|
fifo >>= 8;
|
|
*(buff++) = (BYTE)(fifo & 0xFF);
|
|
}
|
|
|
|
}
|
|
if (SDIO->STA & SDIO_STA_DCRCFAIL) return RES_ERROR;
|
|
|
|
//while(DMASTREAM->CR & DMA_SxCR_EN);
|
|
while(1) {
|
|
__DSB();
|
|
__DMB();
|
|
sdio_status = SDIO->STA;
|
|
if (sdio_status & SDIO_STA_DCRCFAIL) {
|
|
return RES_ERROR;
|
|
}
|
|
if (sdio_status & SDIO_STA_DTIMEOUT) {
|
|
return RES_ERROR;
|
|
}
|
|
|
|
if (sdio_status & SDIO_STA_DATAEND) {
|
|
|
|
if (!(sdio_status & SDIO_STA_RXACT)) {
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
if (card_info.type == SD_V2_HC) {
|
|
addr++;
|
|
} else {
|
|
addr += (1<<BLOCKSIZE);
|
|
}
|
|
}
|
|
return RES_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief SDIO_disk_write
|
|
* @param buff
|
|
* @param sector
|
|
* @param count
|
|
* @warning Not yet implemented
|
|
* @return
|
|
*/
|
|
DRESULT sdio_disk_write(const BYTE *buff, DWORD sector, UINT count)
|
|
{
|
|
uint32_t addr;
|
|
union sdio_status_conv status;
|
|
uint32_t buff_offset = 0;
|
|
int ret;
|
|
|
|
if (sdio_check_write_protection())
|
|
return RES_WRPRT;
|
|
|
|
addr = (card_info.type == SD_V2_HC ? (sector) : (sector * 512));
|
|
|
|
while (count) {
|
|
do {
|
|
sdio_check_status_register_cmd13(card_info.rca, &status.value);
|
|
} while (status.statusstruct.CURRENT_STATE == CURRENT_STATE_PRG ||
|
|
status.statusstruct.CURRENT_STATE == CURRENT_STATE_RCV);
|
|
|
|
if (status.statusstruct.CURRENT_STATE == CURRENT_STATE_STBY) {
|
|
if (sdio_send_select_card_cmd7(card_info.rca))
|
|
return RES_ERROR;
|
|
}
|
|
|
|
do {
|
|
sdio_check_status_register_cmd13(card_info.rca, &status.value);
|
|
} while (status.statusstruct.READY_FOR_DATA != 1);
|
|
|
|
ret = sdio_send_write_block_cmd24(addr);
|
|
if (ret) {
|
|
return RES_ERROR;
|
|
}
|
|
sdio_write_buffer(512, 9, &buff[buff_offset]);
|
|
|
|
buff_offset += 512;
|
|
addr += (card_info.type == SD_V2_HC ? 1 : 512);
|
|
count--;
|
|
}
|
|
|
|
return RES_OK;
|
|
}
|