Add SMPS

* Remove voltage buffer Opamp after TL431PK because it may oscillate
* Replace TL431PK with TL431LI. Stabilized by very large capacitance (> 10uF)
* Add panic passives to differential amplifier in order to avoid oscillaton. Values as they are now should work.
* Remove external ADC. Tests with version v1.1 show that the precision of the STM's ADC is sufficient, (once all oscillations are damped by modifying the circuit)
* Power whole OpAmp circuit with 3.3 volts in order to eliminate the need for the clamping diode at the ADC pin. This diode showed a high reverse current over temperature, which affected the measurement.

reflow-oven-control-pcb-cache.lib

@@ -39,71 +39,6 @@ X 2Y3 9 500 -200 200 L 50 50 1 0 T
 ENDDRAW
 ENDDEF
 #
-# Amplifier_Operational_MCP6401UT-xOT
-#
-DEF Amplifier_Operational_MCP6401UT-xOT U 0 5 Y Y 1 F N
-F0 "U" 0 200 50 H V L CNN
-F1 "Amplifier_Operational_MCP6401UT-xOT" 0 -200 50 H V L CNN
-F2 "" 0 0 50 H I L CNN
-F3 "" 0 0 50 H I C CNN
-ALIAS MCP6401UT-xOT MCP6001U OPA333xxDCK OPA376xxDCK OPA330xxDCK
-$FPLIST
- SOT?23*
- *SC*70*
-$ENDFPLIST
-DRAW
-P 4 0 1 10 -200 200 200 0 -200 -200 -200 200 f
-X V- 2 -100 -300 150 U 50 50 0 1 W
-X V+ 5 -100 300 150 D 50 50 0 1 W
-X + 1 -300 100 100 R 50 50 1 1 I
-X - 3 -300 -100 100 R 50 50 1 1 I
-X ~ 4 300 0 100 L 50 50 1 1 O
-ENDDRAW
-ENDDEF
-#
-# Analog_ADC_MCP3551-EMS
-#
-DEF Analog_ADC_MCP3551-EMS U 0 40 Y Y 1 F N
-F0 "U" -450 300 50 H V L CNN
-F1 "Analog_ADC_MCP3551-EMS" 200 300 50 H V L CNN
-F2 "" 0 0 50 H I C CIN
-F3 "" 0 0 50 H I C CNN
-ALIAS MCP3551-EMS
-$FPLIST
- MSOP*
-$ENDFPLIST
-DRAW
-P 7 0 1 10 -200 250 350 250 350 0 350 -250 -200 -250 -450 0 -200 250 f
-X Vref 1 -100 -400 150 U 50 50 1 1 I
-X Vin+ 2 -500 100 150 R 50 50 1 1 P
-X Vin- 3 -500 -100 150 R 50 50 1 1 P
-X Vss 4 100 -400 150 U 50 50 1 1 W
-X SCK 5 500 100 150 L 50 50 1 1 I
-X SDO/~RDY~ 6 500 0 150 L 50 50 1 1 O
-X ~CS~ 7 500 -100 150 L 50 50 1 1 I
-X Vdd 8 100 400 150 D 50 50 1 1 W
-ENDDRAW
-ENDDEF
-#
-# Connector_Generic_Conn_01x02
-#
-DEF Connector_Generic_Conn_01x02 J 0 40 Y N 1 F N
-F0 "J" 0 100 50 H V C CNN
-F1 "Connector_Generic_Conn_01x02" 0 -200 50 H V C CNN
-F2 "" 0 0 50 H I C CNN
-F3 "" 0 0 50 H I C CNN
-$FPLIST
- Connector*:*_1x??_*
-$ENDFPLIST
-DRAW
-S -50 -95 0 -105 1 1 6 N
-S -50 5 0 -5 1 1 6 N
-S -50 50 50 -150 1 1 10 f
-X Pin_1 1 -200 0 150 R 50 50 1 1 P
-X Pin_2 2 -200 -100 150 R 50 50 1 1 P
-ENDDRAW
-ENDDEF
-#
 # Connector_Generic_Conn_01x05
 #
 DEF Connector_Generic_Conn_01x05 J 0 40 Y N 1 F N
@@ -222,6 +157,54 @@ X Pin_4 4 -200 -200 150 R 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# Connector_TestPoint
+#
+DEF Connector_TestPoint TP 0 30 N N 1 F N
+F0 "TP" 0 270 50 H V C CNN
+F1 "Connector_TestPoint" 0 200 50 H V C CNN
+F2 "" 200 0 50 H I C CNN
+F3 "" 200 0 50 H I C CNN
+$FPLIST
+ Pin*
+ Test*
+$ENDFPLIST
+DRAW
+C 0 130 30 0 1 0 N
+X 1 1 0 0 100 U 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
+# Converter_ACDC_IRM-05-5
+#
+DEF Converter_ACDC_IRM-05-5 PS 0 20 Y Y 1 F N
+F0 "PS" 0 250 50 H V C CNN
+F1 "Converter_ACDC_IRM-05-5" 0 -250 50 H V C CNN
+F2 "Converter_ACDC:Converter_ACDC_MeanWell_IRM-05-xx_THT" 0 -350 50 H I C CNN
+F3 "" 0 -400 50 H I C CNN
+ALIAS IRM-05-5 IRM-05-12 IRM-05-15 IRM-05-24
+$FPLIST
+ Converter*ACDC*MeanWell*IRM*05*THT*
+$ENDFPLIST
+DRAW
+A -185 38 28 -1525 -275 0 1 0 N -210 25 -160 25
+A -135 11 29 292 1508 0 1 0 N -110 25 -160 25
+S -300 200 300 -200 0 1 10 f
+P 2 0 1 0 -210 -25 -110 -25 N
+P 2 0 1 0 0 -100 0 -150 N
+P 2 0 1 0 0 0 0 -50 N
+P 2 0 1 0 0 100 0 50 N
+P 2 0 1 0 0 200 0 150 N
+P 2 0 1 0 110 -25 210 -25 N
+P 2 0 1 0 110 25 130 25 N
+P 2 0 1 0 150 25 170 25 N
+P 2 0 1 0 190 25 210 25 N
+X AC/N 1 -400 -100 100 R 50 50 1 1 W
+X AC/L 2 -400 100 100 R 50 50 1 1 W
+X -Vo 3 400 -100 100 L 50 50 1 1 w
+X +Vo 4 400 100 100 L 50 50 1 1 w
+ENDDRAW
+ENDDEF
+#
 # Device_C
 #
 DEF Device_C C 0 10 N Y 1 F N
@@ -287,38 +270,6 @@ X 4 4 0 -200 50 U 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
-# Device_D_Bridge_+A-A
-#
-DEF Device_D_Bridge_+A-A D 0 0 Y Y 1 F N
-F0 "D" 100 275 50 H V L CNN
-F1 "Device_D_Bridge_+A-A" 100 200 50 H V L CNN
-F2 "" 0 0 50 H I C CNN
-F3 "" 0 0 50 H I C CNN
-$FPLIST
- D*Bridge*
- D*Rectifier*
-$ENDFPLIST
-DRAW
-C -200 0 10 0 1 0 F
-C 0 -200 10 0 1 0 F
-C 0 200 10 0 1 0 F
-C 200 0 10 0 1 0 F
-P 2 0 1 0 -100 150 -50 100 N
-P 2 0 1 0 -50 -100 -100 -150 N
-P 2 0 1 0 100 -50 150 -100 N
-P 2 0 1 0 100 50 150 100 N
-P 4 0 1 0 -150 100 -100 50 -75 125 -150 100 N
-P 4 0 1 0 -100 -50 -150 -100 -75 -125 -100 -50 N
-P 4 0 1 0 50 100 100 150 125 75 50 100 N
-P 4 0 1 0 125 -75 50 -100 100 -150 125 -75 N
-P 5 0 1 0 -200 0 0 -200 200 0 0 200 -200 0 N
-X + 1 300 0 100 L 50 50 1 1 P
-X ~~ 2 0 -300 100 U 50 50 1 1 P
-X - 3 -300 0 100 R 50 50 1 1 P
-X ~~ 4 0 300 100 D 50 50 1 1 P
-ENDDRAW
-ENDDEF
-#
 # Device_Ferrite_Bead_Small
 #
 DEF Device_Ferrite_Bead_Small FB 0 0 N Y 1 F N
@@ -381,6 +332,41 @@ X A 2 150 0 100 L 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# Device_L_Core_Ferrite
+#
+DEF Device_L_Core_Ferrite L 0 40 N N 1 F N
+F0 "L" -50 0 50 V V C CNN
+F1 "Device_L_Core_Ferrite" 110 0 50 V V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+$FPLIST
+ Choke_*
+ *Coil*
+ Inductor_*
+ L_*
+$ENDFPLIST
+DRAW
+A 0 -75 25 -899 899 0 1 0 N 0 -100 0 -50
+A 0 -25 25 -899 899 0 1 0 N 0 -50 0 0
+A 0 25 25 -899 899 0 1 0 N 0 0 0 50
+A 0 75 25 -899 899 0 1 0 N 0 50 0 100
+P 2 0 1 0 40 -110 40 -90 N
+P 2 0 1 0 40 -70 40 -50 N
+P 2 0 1 0 40 -30 40 -10 N
+P 2 0 1 0 40 10 40 30 N
+P 2 0 1 0 40 50 40 70 N
+P 2 0 1 0 40 90 40 110 N
+P 2 0 1 0 60 -90 60 -110 N
+P 2 0 1 0 60 -50 60 -70 N
+P 2 0 1 0 60 -10 60 -30 N
+P 2 0 1 0 60 30 60 10 N
+P 2 0 1 0 60 70 60 50 N
+P 2 0 1 0 60 110 60 90 N
+X 1 1 0 150 50 D 50 50 1 1 P
+X 2 2 0 -150 50 U 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
 # Device_L_Small
 #
 DEF Device_L_Small L 0 10 N N 1 F N
@@ -421,6 +407,43 @@ X ~ 2 0 -150 50 U 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# Device_RF_Shield_Two_Pieces
+#
+DEF Device_RF_Shield_Two_Pieces J 0 40 Y Y 1 F N
+F0 "J" 0 200 50 H V C CNN
+F1 "Device_RF_Shield_Two_Pieces" 0 100 50 H V C CNN
+F2 "" 0 -100 50 H I C CNN
+F3 "" 0 -100 50 H I C CNN
+DRAW
+P 2 0 1 10 -600 -200 -600 -100 N
+P 2 0 1 10 -600 -50 -600 50 N
+P 2 0 1 10 -600 100 -600 200 N
+P 2 0 1 10 -500 300 -400 300 N
+P 2 0 1 10 -400 -300 -500 -300 N
+P 2 0 1 10 -250 -300 -350 -300 N
+P 2 0 1 10 -250 300 -350 300 N
+P 2 0 1 10 -100 -300 -200 -300 N
+P 2 0 1 10 -100 300 -200 300 N
+P 2 0 1 10 -50 -300 50 -300 N
+P 2 0 1 10 50 300 -50 300 N
+P 2 0 1 10 100 -300 200 -300 N
+P 2 0 1 10 200 300 100 300 N
+P 2 0 1 10 250 -300 350 -300 N
+P 2 0 1 10 350 300 250 300 N
+P 2 0 1 10 400 -300 500 -300 N
+P 2 0 1 10 500 300 400 300 N
+P 2 0 1 10 600 -200 600 -100 N
+P 2 0 1 10 600 -50 600 50 N
+P 2 0 1 10 600 100 600 200 N
+P 3 0 1 10 -600 250 -600 300 -550 300 N
+P 3 0 1 10 -550 -300 -600 -300 -600 -250 N
+P 3 0 1 10 550 -300 600 -300 600 -250 N
+P 3 0 1 10 600 250 600 300 550 300 N
+P 4 0 1 10 -700 200 -700 450 700 450 700 200 N
+X Shield 1 0 -400 100 U 50 50 1 1 P
+ENDDRAW
+ENDDEF
+#
 # Device_R_POT
 #
 DEF Device_R_POT RV 0 40 Y N 1 F N
@@ -462,59 +485,6 @@ X 2 2 -200 -100 100 R 50 50 1 1 I
 ENDDRAW
 ENDDEF
 #
-# Device_Transformer_1P_1S
-#
-DEF Device_Transformer_1P_1S T 0 40 Y N 1 F N
-F0 "T" 0 250 50 H V C CNN
-F1 "Device_Transformer_1P_1S" 0 -300 50 H V C CNN
-F2 "" 0 0 50 H I C CNN
-F3 "" 0 0 50 H I C CNN
-DRAW
-A -100 -150 50 899 1 0 1 0 N -100 -100 -50 -150
-A -100 -150 50 -1 -899 0 1 0 N -50 -150 -100 -199
-A -100 -50 50 899 1 0 1 0 N -100 0 -50 -50
-A -100 -50 50 -1 -899 0 1 0 N -50 -50 -100 -99
-A -100 50 50 899 1 0 1 0 N -100 100 -50 50
-A -100 50 50 -1 -899 0 1 0 N -50 50 -100 1
-A -100 150 50 899 1 0 1 0 N -100 200 -50 150
-A -100 150 50 -1 -899 0 1 0 N -50 150 -100 101
-A 100 -50 50 899 -1799 0 1 0 N 100 0 51 -50
-A 100 -50 50 1799 -899 0 1 0 N 51 -50 100 -99
-A 100 50 50 899 -1799 0 1 0 N 100 100 51 50
-A 100 50 50 1799 -899 0 1 0 N 51 50 100 1
-A 100 150 50 899 -1799 0 1 0 N 100 200 51 150
-A 100 150 50 1799 -899 0 1 0 N 51 150 100 101
-A 101 -150 50 910 -1799 0 1 0 N 101 -100 52 -150
-A 101 -150 50 -912 -1799 0 1 0 N 101 -199 52 -150
-P 2 0 1 0 -25 200 -25 -200 N
-P 2 0 1 0 25 -200 25 200 N
-X AA 1 -400 200 300 R 50 50 1 1 P
-X AB 2 -400 -200 300 R 50 50 1 1 P
-X SA 3 400 -200 300 L 50 50 1 1 P
-X SB 4 400 200 300 L 50 50 1 1 P
-ENDDRAW
-ENDDEF
-#
-# Diode_1N4448W
-#
-DEF Diode_1N4448W D 0 40 N N 1 F N
-F0 "D" 0 100 50 H V C CNN
-F1 "Diode_1N4448W" 0 -100 50 H V C CNN
-F2 "Diode_SMD:D_SOD-123" 0 -175 50 H I C CNN
-F3 "" 0 0 50 H I C CNN
-ALIAS 1N4148W BAV16W 1N4448W MMSD4148
-$FPLIST
- D*SOD?123*
-$ENDFPLIST
-DRAW
-P 2 0 1 10 -50 50 -50 -50 N
-P 2 0 1 0 50 0 -50 0 N
-P 4 0 1 8 50 50 50 -50 -50 0 50 50 N
-X K 1 -150 0 100 R 50 50 1 1 P
-X A 2 150 0 100 L 50 50 1 1 P
-ENDDRAW
-ENDDEF
-#
 # Jumper_SolderJumper_2_Open
 #
 DEF Jumper_SolderJumper_2_Open JP 0 0 Y N 1 F N
@@ -684,6 +654,32 @@ X 1 1 0 -100 100 U 50 50 1 1 I
 ENDDRAW
 ENDDEF
 #
+# Memory_EEPROM_25LCxxx
+#
+DEF Memory_EEPROM_25LCxxx U 0 20 Y Y 1 F N
+F0 "U" -300 250 50 H V C CNN
+F1 "Memory_EEPROM_25LCxxx" 100 -250 50 H V L CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+ALIAS BR25Sxxx CAT250xxx AT25xxx
+$FPLIST
+ DIP*W7.62mm*
+ SOIC*3.9x4.9mm*
+ TSSOP*4.4x3mm*P0.65mm*
+$ENDFPLIST
+DRAW
+S -300 200 300 -200 1 1 10 f
+X ~CS 1 -400 -100 100 R 50 50 1 1 I
+X MISO 2 400 -100 100 L 50 50 1 1 T
+X ~WP 3 -400 100 100 R 50 50 1 1 I
+X GND 4 0 -300 100 U 50 50 1 1 W
+X MOSI 5 400 0 100 L 50 50 1 1 I
+X SCK 6 400 100 100 L 50 50 1 1 I
+X ~HOLD 7 -400 0 100 R 50 50 1 1 I
+X VCC 8 0 300 100 D 50 50 1 1 W
+ENDDRAW
+ENDDEF
+#
 # Power_Protection_USBLC6-2SC6
 #
 DEF Power_Protection_USBLC6-2SC6 U 0 0 Y Y 1 F N
@@ -734,23 +730,23 @@ X IO1 6 -500 100 200 R 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
-# Reference_Voltage_TL431PK
+# Reference_Voltage_TL431DBZ
 #
-DEF Reference_Voltage_TL431PK U 0 20 N N 1 F N
+DEF Reference_Voltage_TL431DBZ U 0 20 N N 1 F N
 F0 "U" -100 100 50 H V C CNN
-F1 "Reference_Voltage_TL431PK" 0 -100 50 H V C CNN
+F1 "Reference_Voltage_TL431DBZ" 0 -100 50 H V C CNN
-F2 "Package_TO_SOT_SMD:SOT-89-3" 0 -150 50 H I C CIN
+F2 "Package_TO_SOT_SMD:SOT-23" 0 -150 50 H I C CIN
 F3 "" 0 0 50 H I C CIN
 $FPLIST
- SOT*89*
+ SOT?23*
 $ENDFPLIST
 DRAW
 P 3 0 1 0 -50 0 0 0 50 0 N
 P 3 0 1 0 -30 30 30 0 -30 -30 F
 P 4 0 1 10 20 -40 30 -30 30 30 30 30 N
-X REF 1 0 100 100 D 50 50 1 1 P
+X K 1 100 0 100 L 50 50 1 1 P
-X A 2 -100 0 50 R 50 50 1 1 P
+X REF 2 0 100 100 D 50 50 1 1 P
-X K 3 100 0 50 L 50 50 1 1 P
+X A 3 -100 0 100 R 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
@@ -780,28 +776,6 @@ F0 "U" -150 125 50 H V C CNN
 F1 "Regulator_Linear_AZ1117-3.3" 0 125 50 H V L CNN
 F2 "" 0 250 50 H I C CIN
 F3 "" 0 0 50 H I C CNN
-$FPLIST
- SOT?223*
- SOT?89*
- TO?220*
- TO?252*
- TO?263*
-$ENDFPLIST
-DRAW
-S -200 75 200 -200 0 1 10 f
-X GND 1 0 -300 100 U 50 50 1 1 W
-X VO 2 300 0 100 L 50 50 1 1 w
-X VI 3 -300 0 100 R 50 50 1 1 W
-ENDDRAW
-ENDDEF
-#
-# Regulator_Linear_AZ1117-5.0
-#
-DEF Regulator_Linear_AZ1117-5.0 U 0 10 Y Y 1 F N
-F0 "U" -150 125 50 H V C CNN
-F1 "Regulator_Linear_AZ1117-5.0" 0 125 50 H V L CNN
-F2 "" 0 250 50 H I C CIN
-F3 "" 0 0 50 H I C CNN
 ALIAS AZ1117-1.5 AZ1117-1.8 AZ1117-2.5 AZ1117-2.85 AZ1117-3.3 AZ1117-5.0
 $FPLIST
  SOT?223*
@@ -818,32 +792,26 @@ X VI 3 -300 0 100 R 50 50 1 1 W
 ENDDRAW
 ENDDEF
 #
-# Sensor_Temperature_DS18B20
+# Transistor_BJT_BC818
 #
-DEF Sensor_Temperature_DS18B20 U 0 40 Y Y 1 F N
+DEF Transistor_BJT_BC818 Q 0 0 Y N 1 F N
-F0 "U" -150 250 50 H V C CNN
+F0 "Q" 200 75 50 H V L CNN
-F1 "Sensor_Temperature_DS18B20" 250 250 50 H V C CNN
+F1 "Transistor_BJT_BC818" 200 0 50 H V L CNN
-F2 "Package_TO_SOT_THT:TO-92_Inline" -1000 -250 50 H I C CNN
+F2 "Package_TO_SOT_SMD:SOT-23" 200 -75 50 H I L CIN
-F3 "" -150 250 50 H I C CNN
+F3 "" 0 0 50 H I L CNN
-ALIAS DS1822 DS18B20 DS18S20 DS1821C
+ALIAS BC818 BC846 BC847 BC848 BC849 BC850 MMBT3904 MMBT5550L MMBT5551L
 $FPLIST
- TO*92*
+ SOT?23*
 $ENDFPLIST
 DRAW
-A -130 125 25 1 1799 0 1 10 N -105 125 -155 125
+C 50 0 111 0 1 10 N
-C -130 -100 50 0 1 10 F
+P 2 0 1 0 25 25 100 100 N
-S -200 200 200 -200 0 1 10 f
+P 3 0 1 0 25 -25 100 -100 100 -100 N
-S -105 -75 -155 0 0 1 10 F
+P 3 0 1 20 25 75 25 -75 25 -75 N
-P 2 0 1 10 -155 25 -130 25 N
+P 5 0 1 0 50 -70 70 -50 90 -90 50 -70 50 -70 F
-P 2 0 1 10 -155 50 -130 50 N
+X B 1 -200 0 225 R 50 50 1 1 I
-P 2 0 1 10 -155 75 -130 75 N
+X E 2 100 -200 100 U 50 50 1 1 P
-P 2 0 1 10 -155 100 -130 100 N
+X C 3 100 200 100 D 50 50 1 1 P
-P 2 0 1 10 -155 125 -155 0 N
-P 2 0 1 10 -155 125 -130 125 N
-P 2 0 1 10 -105 125 -105 0 N
-X GND 1 0 -300 100 U 50 50 1 1 W
-X DQ 2 300 0 100 L 50 50 1 1 B
-X VDD 3 0 300 100 D 50 50 1 1 W
 ENDDRAW
 ENDDEF
 #
@@ -879,6 +847,21 @@ X D 3 100 200 100 D 50 50 1 1 P
 ENDDRAW
 ENDDEF
 #
+# power_+3.3VA
+#
+DEF power_+3.3VA #PWR 0 0 Y Y 1 F P
+F0 "#PWR" 0 -150 50 H I C CNN
+F1 "power_+3.3VA" 0 140 50 H V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+DRAW
+P 2 0 1 0 -30 50 0 100 N
+P 2 0 1 0 0 0 0 100 N
+P 2 0 1 0 0 100 30 50 N
+X +3.3VA 1 0 0 0 U 50 50 1 1 W N
+ENDDRAW
+ENDDEF
+#
 # power_+3V3
 #
 DEF power_+3V3 #PWR 0 0 Y Y 1 F P
@@ -910,21 +893,6 @@ X +5V 1 0 0 0 U 50 50 1 1 W N
 ENDDRAW
 ENDDEF
 #
-# power_+5VA
-#
-DEF power_+5VA #PWR 0 0 Y Y 1 F P
-F0 "#PWR" 0 -150 50 H I C CNN
-F1 "power_+5VA" 0 140 50 H V C CNN
-F2 "" 0 0 50 H I C CNN
-F3 "" 0 0 50 H I C CNN
-DRAW
-P 2 0 1 0 -30 50 0 100 N
-P 2 0 1 0 0 0 0 100 N
-P 2 0 1 0 0 100 30 50 N
-X +5VA 1 0 0 0 U 50 50 1 1 W N
-ENDDRAW
-ENDDEF
-#
 # power_+5VL
 #
 DEF power_+5VL #PWR 0 0 Y Y 1 F P
@@ -940,21 +908,6 @@ X +5VL 1 0 0 0 U 50 50 1 1 W N
 ENDDRAW
 ENDDEF
 #
-# power_+8V
-#
-DEF power_+8V #PWR 0 0 Y Y 1 F P
-F0 "#PWR" 0 -150 50 H I C CNN
-F1 "power_+8V" 0 140 50 H V C CNN
-F2 "" 0 0 50 H I C CNN
-F3 "" 0 0 50 H I C CNN
-DRAW
-P 2 0 1 0 -30 50 0 100 N
-P 2 0 1 0 0 0 0 100 N
-P 2 0 1 0 0 100 30 50 N
-X +8V 1 0 0 0 U 50 50 1 1 W N
-ENDDRAW
-ENDDEF
-#
 # power_Earth
 #
 DEF power_Earth #PWR 0 0 Y Y 1 F P
@@ -984,6 +937,46 @@ X GND 1 0 0 0 D 50 50 1 1 W N
 ENDDRAW
 ENDDEF
 #
+# shimatta_analog_MCP6V34
+#
+DEF shimatta_analog_MCP6V34 U 0 40 Y Y 5 L N
+F0 "U" 450 -50 50 H V C CNN
+F1 "shimatta_analog_MCP6V34" 500 50 50 H V C CNN
+F2 "" 0 0 50 H I C CNN
+F3 "" 0 0 50 H I C CNN
+DRAW
+T 0 150 -200 50 0 2 0 A Normal 0 C C
+T 0 150 -200 50 0 3 0 B Normal 0 C C
+T 0 150 -200 50 0 4 0 C Normal 0 C C
+T 0 150 -200 50 0 5 0 D Normal 0 C C
+S 0 0 400 -750 1 1 0 f
+P 2 1 1 0 100 -450 50 -450 N
+P 2 1 1 0 100 -350 50 -350 N
+P 2 1 1 0 200 -450 200 -750 N
+P 2 1 1 0 200 0 200 -350 N
+P 2 1 1 0 300 -400 350 -400 N
+P 5 1 1 0 100 -300 100 -450 100 -500 300 -400 100 -300 F
+P 4 2 1 0 0 0 0 -400 350 -200 0 0 f
+P 4 3 1 0 0 0 0 -400 350 -200 0 0 f
+P 4 4 1 0 0 0 0 -400 350 -200 0 0 f
+P 4 5 1 0 0 0 0 -400 350 -200 0 0 f
+X VSS 11 200 -850 100 U 50 50 1 1 W
+X VDD 4 200 100 100 D 50 50 1 1 W
+X ~ 1 450 -200 100 L 50 50 2 1 O
+X - 2 -100 -300 100 R 50 50 2 1 I
+X + 3 -100 -100 100 R 50 50 2 1 I
+X + 5 -100 -100 100 R 50 50 3 1 I
+X - 6 -100 -300 100 R 50 50 3 1 I
+X ~ 7 450 -200 100 L 50 50 3 1 O
+X + 10 -100 -100 100 R 50 50 4 1 I
+X ~ 8 450 -200 100 L 50 50 4 1 O
+X - 9 -100 -300 100 R 50 50 4 1 I
+X + 12 -100 -100 100 R 50 50 5 1 I
+X - 13 -100 -300 100 R 50 50 5 1 I
+X ~ 14 450 -200 100 L 50 50 5 1 O
+ENDDRAW
+ENDDEF
+#
 # shimatta_connectors_10PIN_JTAG_SWD
 #
 DEF shimatta_connectors_10PIN_JTAG_SWD J 0 40 Y Y 1 F N

reflow-oven-control-pcb.pro

@@ -1,4 +1,4 @@
-update=Fri 03 Jan 2020 08:43:13 PM CET
+update=Tue 18 Feb 2020 09:42:41 PM CET
 version=1
 last_client=kicad
 [general]
@@ -12,16 +12,6 @@ NetIExt=net
 version=1
 LibDir=
 [eeschema/libraries]
-[schematic_editor]
-version=1
-PageLayoutDescrFile=
-PlotDirectoryName=
-SubpartIdSeparator=0
-SubpartFirstId=65
-NetFmtName=Pcbnew
-SpiceAjustPassiveValues=0
-LabSize=50
-ERC_TestSimilarLabels=1
 [pcbnew]
 version=1
 PageLayoutDescrFile=
@@ -264,3 +254,13 @@ uViaDrill=0.1
 dPairWidth=0.21
 dPairGap=0.25
 dPairViaGap=0.25
+[schematic_editor]
+version=1
+PageLayoutDescrFile=
+PlotDirectoryName=
+SubpartIdSeparator=0
+SubpartFirstId=65
+NetFmtName=Pcbnew
+SpiceAjustPassiveValues=0
+LabSize=50
+ERC_TestSimilarLabels=1

sym-lib-table

@@ -1,3 +1,4 @@
 (sym_lib_table
   (lib (name shimatta_connectors)(type Legacy)(uri ${SHIMATTA_DIR}/schematics/shimatta_connectors.lib)(options "")(descr ""))
+  (lib (name shimatta_analog)(type Legacy)(uri ${SHIMATTA_DIR}/schematics/shimatta_analog.lib)(options "")(descr ""))
 )